GMT800

Motor vehicle platform

The GMT800 was a General Motors full-size truck platform used from the 1999 through 2009 model years. It is the foundation for the Chevrolet Silverado and GMC Sierra pickups; and the derivative GMT820 and GMT830 versions for the Chevrolet Tahoe/GMC Yukon and the Chevrolet Suburban/GMC Yukon XL full-size SUVs, respectively.

Nº Q5513800 ★★

Peu commune · Savoirs

GMT800

Motor vehicle platform

Texte en anglais

The GMT800 was a General Motors full-size truck platform used from the 1999 through 2009 model years. It is the foundation for the Chevrolet Silverado and GMC Sierra pickups; and the derivative GMT820 and GMT830 versions for the Chevrolet Tahoe/GMC Yukon and the Chevrolet Suburban/GMC Yukon XL full-size SUVs, respectively.

Dernier prix

—

Prix plancher

—

Médiane 7 j

—

Ventes 30 j

0

Fourchette 30 j

—

En circulation

0

Cours

Voir le tableau
Datemédiane MinMaxventes

Historique des ventes

Dernière vente
—
Moyenne 30 j
—
Plus bas 30 j
—
Plus haut 30 j
—
Ventes 7 j
0
Ventes 30 j
0

Aucune vente pour l'instant.

Ventes anonymes : ni acheteur ni vendeur. Les chiffres ne comptent que les ventes entre joueurs.

Sur Wikipédia

Texte en anglais Pas encore d'article dans ta langue : extrait en anglais.

The GMT800 was a General Motors full-size truck platform used from the 1999 through 2009 model years. It is the foundation for the Chevrolet Silverado and GMC Sierra pickups; and the derivative GMT820 and GMT830 versions for the Chevrolet Tahoe/GMC Yukon and the Chevrolet Suburban/GMC Yukon XL full-size SUVs, respectively. This platform was the successor to the GMT400 series of C/K pickups and SUVs, and was replaced for 2007 by the GMT900 line. The GMT800 frames were manufactured by Magna International in Ramos Arizpe, Coahuila, Mexico; and St. Thomas, Ontario, Canada. Trucks were assembled in Oshawa, Ontario; Pontiac, Michigan; Fort Wayne, Indiana; Flint, Michigan; and Silao, Mexico; for pickup and chassis cab models, and Silao, Mexico; Janesville, Wisconsin; and Arlington, Texas; for SUV models. The GMT820-based Hummer H2 was built under contract by AM General at a specially-constructed plant in Mishawaka, Indiana. A GMT810 two-door SUV variant was designed and prototyped, but was not put into production. The GMT800 introduced a three-section frame system. This could be mixed and matched depending on the wheelbase, GVWR, and body type fitted to the platform, rather than a single-piece long frame. The front section was hydroformed, while the middle and rear sections were roll formed or stamped, depending on application. This gives greater flexibility to the platform. A total of four front modules, seven midsections, and four rear sections were designed, and supported nearly 40 truck configurations. All models featured an independent front suspension. Torsion bars were used on all 4WD models, plus all 2WD 1500-series SUVs and 1500HD/2500HD/3500 pickup and chassis-cab models. On 2WD models, coil springs were used on most 1500-series pickups and all 1999–2000 2500-series models. The GMT800 pickup models used a rear leaf-spring suspension, while the GMT820/830 SUV models used a five-link coil-spring suspension. (The 2500-series GMT830 SUV models...

Texte : Wikipédia en anglais, CC BY-SA 4.0. · Image : IFCAR (Public domain) ·

Cartes voisines

Voir la fiche

Confirmation